Internal Engine Cleaner Engine Decarbonizing Machine For Combustion
Chamber
Compared to other carbon cleaner:
1. Needs to connect the engine pipelines for dripping the cleaning
agent.
2. It can clean five engine parts like combustion chamber, three
way catalytic converter, intake and so on.
3. Cleaning catalytic converter has two methods, water based and
oil based cleaning agent.
4. More cleaner than other machine for the special cleaning agent
with chemicals.
5. It is no need to dismantle the whole engine but some parts need
to be take down.
Working principle:
TD-501 is a machine should use the special cleaning agent adjusting
to the engine part, which means that it works as a medium between
the cleaning agent and the engine. 95% of cleaning agent will be
sent into the engine part through the special pipeline of engine
carbon cleaning machine, and then burn with the carbon deposit in
the engine. Finally they will be consumed and become the gases
exhaust from the pipe. Therefore, when finishing the carbon
cleaning, the user should step on the gas to let the dirt outlet.
So we can see the exhaust become white or black while step on the
gas or some carbon deposit.
Parameters:
| Model Number | TD-501 |
| Product Name | Engine carbon cleaning machine |
| Voltage | DC 12V |
| Rated Power | 150W |
| Working Pressure | 0-1.6 Mpa |
| Weight | 38kg |
| Size | 43*40*100cm |
| Package Dimension | 47*41*110cm |
| Ambient temperature range | -5°C~50°C |
| Endoscope Pixel | 1.3 millions |
| Package | Wooden case |
| Working medium | Chemical cleaning agent |
| Application | Gasoline car engines |
| Usage | Car engine carbon clean |
| Color | Red/Green |
| Type | Other car care product |
The cleaning methods of Aqueous ternary:
1. Check the engine and ternary catalytic converters for
malfunction;
2. Drive the car to a sloping place or top the front for better
discharge of water during construction;
3. Remove the pre-oxygen sensor and unplug all the other oxygen
sensors (if there are 2 or 4 oxygen sensors, remove the whole
plugs)
4. Add the ternary catalytic cleaning agent and water to the
washing machine according to the prescribed ratio (1 bottle of
cleaning agent to 10 L water). The dirty one can be increased the
concentration properly.
5. Connect the nozzle to the oxygen sensor, start the engine, keep
running at the idle speed. Then turn on the power switch of the
equipment, inject the cleaning liquid into the car and soak for 5
minutes.
6. Then the ternary catalytic reductant and water are added to the
cleaning machine according to the prescribed ratio (1 bottle of
cleaning agent to 10 L water), the power switch of the equipment is
turned on and the cleaning liquid is injected into the car.
7. Step on the throttle and drain the fluid out of the exhaust pipe
until the exhaust pipe runs out of water.
8. Restore the line, shut off the engine, and the cleaning is over.
9. Notice:
a. Prevent water from pouring back. Some models of oxygen sensors
or three-way catalytic converters are at the same level with the
engine, or higher than the engine, please do not use this method of
cleaning, recommended other cleaning methods.
b. Old cars are not recommended for cleaning. Because the car is
too old, many parts are aging and can be damaged at touch, such as
oxygen sensors and ternary catalytic converters. Ternary catalytic
converters close to the failure period or are not recommended
cleaning, we must be clear to car owners in advance of the risk.
c. The turbocharged car can not speed up when cleaning, can only
idle, after cleaning, the water has been drained almost can slowly
increase the throttle, let the water continue to drain out, but can
not accelerate quickly.
d. Make sure the exhaust pipe is completely drained.
e. All operation should wear acid-proof gloves, do not let the skin
and cleaning liquid contact. Immediately rinse or consult a doctor
with plenty of water as soon as the eye or skin gradually enters.
